RØDE Wireless GO Gen 3 2-Person Wireless Microphone System – Black

RØDE WIRELESS GO · GEN 3

Wireless audio with an independent recording on each speaker.

RØDE Wireless GO Gen 3 is a two-person wireless microphone system for cameras, computers and mobile devices. Two transmitters combine built-in microphones, locking external-microphone inputs and local 32-bit-float recording. The receiver supplies analogue and USB audio, with level controls, monitoring modes and flexible two-channel routing for interviews, video and streaming.

Record locally in 32-bit float as well as sending wireless audio

Each transmitter contains 32 GB of storage for more than 40 hours of manufacturer-rated 32-bit-float WAV recording. These separate local recordings can remain available when the wireless feed experiences a dropout. They also give compatible editing software room to rebalance recording levels afterward.

32-bit-float recovery applies to the transmitter’s on-board files. It does not turn a camera recording or the live transmitted output into a 32-bit-float recording, and it cannot remove distortion caused by exceeding the physical microphone’s maximum sound level.

Manual recording is the default: start and stop with each transmitter’s record control. Always mode records whenever that transmitter is powered, even without a receiver. A configured receiver Ø button can control both recordings; in Always mode it starts a new file rather than stopping continuous capture.

Copy important files out before reuse. When storage fills, older recordings are overwritten, and files cannot be individually deleted on the unit. Access WAV files through removable storage or use RØDE Central desktop for markers, dropout indicators, normalisation and selective or batch export. Central can also export normalised 24-bit PCM files.

Set speech levels automatically or take manual control

GainAssist offers Auto mode for a more consistent output and Dynamic mode for retaining more variation in the performance. It can be disabled independently for the transmitters and a supported receiver-headset microphone. With GainAssist off, transmitter input gain can be set manually from 0 to 30 dB in 1 dB steps.

GainAssist does not process the transmitter’s on-board recordings. Set up the live feed for the camera or application, and treat the local file as a separate post-production recording.

Receiver analogue output gain adjusts from −30 to 0 dB in 3 dB steps. That control changes the 3.5 mm feed, not USB output level. Choose Manual gain or a suitable camera preset, and match the camera’s own microphone-input setting. Up to ten camera presets can be stored, including custom presets.

Choose how two output channels carry the sources

Merged mode combines the active sources into both output channels. Split mode places TX1 and TX2 on the left and right channels, preserving separate speaker tracks for editing. Both USB and analogue outputs provide two channels.

Safety mode uses merged routing: the main mix is sent left, with a second copy 10 dB lower on the right. It provides a quieter live safety channel while giving up separate left/right transmitter routing.

A compatible TRRS headset microphone can add a receiver-side source when using USB output. In Split mode with that source enabled, both transmitter signals combine on the left and the receiver microphone occupies the right. Three sources therefore do not become three independently recorded output tracks.

Monitor using the shared 3.5 mm socket

The receiver’s shared 3.5 mm connection supports camera output, Headphones and Headset modes. Headphone mode engages a higher-power amplifier for monitoring. Headset mode can use a compatible TRRS microphone connection; other microphone wiring may require an appropriate separate adapter.

The same socket cannot hold a camera audio cable and headphones at the same time. Headset-microphone recording uses the USB output. Headphones, headsets and any required adapters are not included.

Use Direct Connect with RØDE Capture on a compatible iPhone

Current firmware can connect up to two transmitters directly to RØDE Capture over Bluetooth without the receiver. This receiver-free route supports merged or split capture and transmitter GainAssist and LED controls in the app.

RØDE specifies transmitter firmware 2.0.8 or later and a current compatible Capture app for this feature. Update using Central desktop, including Optional Updates if needed, and keep the receiver switched off during Direct Connect pairing.

Direct Connect is a Capture workflow for supported iOS devices. It does not provide general Bluetooth recording in other apps or Android Direct Connect. Use the receiver for those compatible wired recording routes. Hardware USB requirements list macOS 11+, Windows 10+, iOS 14+ and Android 11+; the app and phone model must also meet their own requirements.

What is included

• 2 × Wireless GO Gen 3 transmitters
• 1 × Wireless GO Gen 3 dual-channel receiver
• 1 × SC2 3.5 mm TRS-to-TRS camera cable
• 1 × SC21 USB-C-to-Lightning cable
• 1 × SC22 USB-C-to-USB-C cable
• 1 × SC33 three-unit USB charging hub
• 1 × carry pouch
• 3 × twist-lock furry windshields

External lavaliers, headphones/headsets, USB-A cabling and the rechargeable Charge Case+ are separate purchases.

Check the features needed for your production

This is the black Wireless GO third-generation kit, manufacturer model WIGOGEN3. It has no timecode function. The transmitter’s 32-bit-float file is an independent local recording, not the format of every connected camera or the wireless live output.

Explore the microphones category and RØDE range at AX Store Kuwait, or follow the official Wireless GO Gen 3 setup guide for connection and recording configuration.